GE Dishwasher Fills With Water Then Stops: 9 Suitable Fixes

One of the common problems that many complained about with the GE dishwasher is that the GE dishwasher fills with water then stops. When we faced this, it seemed too troublesome and felt like kicking the dishwasher. 

However, obviously, kicking is not the right solution. We got into the problem and found assembling issues, door switch issues, drainage issues, and clogged filters may arise the functionality issue. To fix it, you need to inspect each area and take necessary steps like cleaning or replacing. 

Ge Dishwasher Fills With Water Then Stops: 9 Reasons And Solutions 

Here are some common issues that may cause your GE dishwasher functionality problems. After our inspection, here is what we found: 

Door Switch Issue

When you don’t lock your dishwasher door properly, it won’t get the sensory input to start the cycle. Therefore, even if the dishwasher is filled with water, you can’t run it. Oftentimes, door switch issues cause a malfunction in the GE dishwasher. 

Solution: 

• Check that the dishwasher door is closed securely. 
• If the door doesn’t lock correctly, readjust or replace the door latch. 
• Also, check the door switch for continuity using a multimeter. If it’s faulty, replace it.

Float Assembly Stuck

The second reason why your dishwasher might not work after filling it out can be when the float assembly is stuck. It is a small device located at the bottom of the dishwasher tub. When the device is stuck, it can mislead the dishwasher into assuming there’s already enough water, causing it to stop filling. 

Therefore, you might think that there’s enough water, but in reality, the dishwasher is not filled adequately to step into the next process. 

Solution:

• Inspect the float assembly and ensure that it moves up and down freely. 
• Clean debris around the float. 
• If the float is damaged, replace it.

Water Inlet Valve Problem

The water inlet valve lets water into the dishwasher during the filling cycle. If the valve is defective, or clogged, it may not open to allow water in, leading to the dishwasher stopping after filling.

Solution: 

• Test the water inlet valve with a multimeter to confirm it’s acquiring the suitable voltage and has continuity.
• If there’s an issue with the electrical signal, change the wiring or replace the component. 
• If your water inlet valve itself is faulty or clogged, replace it.

Clogged Filters

Clogged filters in the dishwasher cause the dishwasher to stop after filling due to the water flow obstruction. This can be reasoned by dirt or debris accumulation.

Solution: 

• Remove and thoroughly clean the dishwasher’s filters and spray arms. 
• Ensure there are no blockages that can disrupt the water flow. 
• Reinstall the clean components properly to ensure proper flow. 

Drainage Issues

When your previous cycle is not drained properly, your dishwasher won’t start for a new cycle. You might mistake the previous standing water thinking that this is the new water, but when your dishwasher drainage is faulty, it won’t fill new water in. 

Solution: 

• Inspect the drain hose for clogs, or blockages. If you find anything, clean the drainage system properly to continue operating your dishwasher. 
• Ensure that your dishwasher is connected appropriately to the sink drain. 

Control Board Malfunction

The management of your dishwasher’s cycles starts from the control board. If there are any issues in there, the management will fail and your dishwasher will fail to operate. Therefore, if your dishwasher fills with water and then stops, this might be the reason why. 

Solution: 

• Check the dishwasher’s control board for signs of damage.
• If you notice something like burnt-out components or visible damage, it may need to be replaced.
• Look for electrical issues that might disturb the operation.
• Also, check if the control board is connected properly in the right place or not. 

Solenoid Malfunction 

Most GE dishwashers have drain solenoids which help the drain to open up while draining a cycle. If that doesn’t work properly, this will lead to malfunctions in your dishwasher. 

Solution: 

• You need to change the impeller if your dishwasher has solenoid issues. Nothing else will work in this case.

Faulty Sensor

Your dishwasher operates relying on the sensors. The sensors signal when to start and stop. So, if your GE dishwasher is signal operated, there might be something wrong with the sensors which is why it fails to start a cycle after filling the water. 

Solution: 

• If your dishwasher’s sensors are faulty, you need to consult a professional. In this case, you can’t do anything on your own.

Water Supply Problems

Sometimes, external factors like low water pressure or a disturbed water supply line can restrict water flow to the dishwasher, leading to incomplete filling. Although you might not notice it from the beginning, this might be why your dishwasher is not starting the cycle. 

Solution: 

• Ensure the dishwasher’s water supply line is free from blockages. 
• Check that there is adequate water pressure.
• If nothing works, consult a professional to inspect the issue. 

How To Investigate That Your GE Dishwasher Has Issues? 

Investigating issues with your GE dishwasher requires patience and a systematic approach to identifying the root cause. As the filling and stops to operate problem might be caused by several underlying issues, you need to check every component serially to address the actual problem. 

You need to notice external factors like signs of damage, water leaking, and power supply functionality. If that’s okay, move to the door latch. Verify that the dishwasher’s door is closing properly and latching securely. 

Afterward, you need to inspect the dishwasher’s drainage, water supply, and filters to find debris or dirt accumulation. Remove the bottom rack and check the drain area for any leftover food particles that might impede proper drainage. 

Lastly, check out the dishwasher’s float assembly, filters and spray arms. If nothing shows up, the problem might be inside the components or electricity supply. In this case, you will need to seek help from a professional for further inspection. 

Further To Explore 

Calling In The Closure 

The GE dishwasher fills with water then stops problems are quite common among the users. But following the given suggestions can get you the right help in times of need. As we have been through it, we can say there’s nothing much to worry about. You can follow the tactics and make your dishwasher functional again!